This standard specifies basic functions and performance requirements for vehicle security alarm network systems, which are the fundamental basis for system design, equipment selection, equipment installation and system function & performance inspections.
This standard is applicable to the design, inspection and acceptance of motor vehicle security alarm network system for urban areas.
2 Normative References
The following documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated reference, subsequent amendments to (excluding any corrigendum), or revisions of, any of these publications do not apply. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. For any undated references, the latest edition of the document referred to applies.
GB/T 2423.1-2001 Environmental Testing for Electric and Electronic Products - Part 2: Test methods Tests A: Cold (idt IEC60068-2-1:1990)
GB/T 2423.2-2001 Environmental Testing for Electric and Electronic Products - Part 2: Test Methods - Tests B: Dry Heat (idt IEC 60068-2-2:1974)
GB/T 2423.3-1993 Basic Environmental Testing Procedures for Electric and Electronic Products - Test Ca: Damp Heat, Steady State (eqv IEC 68-2-3:1984)
GB/T 2423.5-1995 Environmental Testing for Electric and Electronic Products - Part 2: Test Methods - Test Ea and Guidance: Shock (idt IEC 68-2-27:1987)
GB/T 2423.10-1995 Environmental Testing for Electric and Electronic Products - Part 2: Test Methods - Test Fc and Guidance: Vibration (Sinusoidal) (idt IEC 68-2-6:1982)
GB 9254-1998 Information Technology Equipment - Radio Disturbance Characteristics - Limits and Methods of Measurement (idt CISPR 22:1997)
GB 15740-1995 Motor Vehicle-Protective Devices against Unauthorized Use-Performance Requirements (eqv ECER 1:1981)
GB 16796-1997 Safety Requirements and Test Methods for Security Alarm Equipment
GB/T 17626.2-1998 Electromagnetic Compatibility - Testing and Measurement Techniques - Electrostatic Discharge Immunity Test (idt IEC 61000-4-2:1995)
GB/T 17626.3-1998 Electromagnetic Compatibility - Testing and Measurement Techniques - Radiated Radio-Frequency Electromagnetic Field Immunity Test (idt IEC 61000-4-3:1995)
GB/T 17626.4-1998 Electromagnetic Compatibility - Testing and Measurement Techniques - Electrical Fast Transient/Burst Immunity Test (idt IEC 61000-4-4:1995)
GB/T 17626.5-1999 Electromagnetic Compatibility - Testing and Measurement Techniques - Surge(impact) Immunity Test (idt IEC 61000-4-5:1995)
GB 50343-2004 Technical Code for Protection Against Lightning of Building Electronic Information System
GB 50348-2004 Technical Code for Engineering of Security and Protection System
GA 2-1999 Vehicle Security Alarm Systems - Passenger Cars (eqv IEC 839-10-1:1995)
GA 308-2001 Acceptance Check Criterion of Security and Alarm Systems
GA 366-2001 Vehicle Security Alarm Equipment Installation Regulation
GA/T 440-2003 Interface between Alarm Control Equipment and Communication Terminating Equipment in Vehicle Security Alarm Network System
3 Terms and Definitions
For the purposes of this standard, the terms and definitions specified in GA 2-1999 and GA/T 440-2003 and those listed below apply.
3.1
vehicle security alarm network system
an information system composed of vehicle equipment, communication network, monitoring center and position service unit, and incorporating anti-theft and -robbery functions. Vehicle equipment, while providing security protection and local alarming functions for the vehicle, also transmits information, e.g. alarming, to the monitoring center for processing by means of wireless and wired communication networks and the monitoring center then sends command to the vehicle via communication network to implement remote control and monitor over the vehicle. Where necessary, the system dispatches alarm-processing vehicles and persons by means of tracing the alarming vehicle, to realize robbery prevention and aid.
