1. Scope
This national Standard specifies the environmental test method and severities of fire electronic products.
This Standard is applicable to the environmental test for the fire electronic products used in general installation site, environmental test method and severities for the fire electronic products used in special installation site. Unless otherwise specified in other related standards, they shall all comply with this Standard.
2. Normative References
The following standards contain provisions which, through reference in this text, constitute provisions of this Standard. For dated reference, subsequent amendments (excluding content of corrigenda) to, or revisions of, any of these publications do not apply. However, Parties to agreements based on this Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below.
GB/T 2422-1995 Environmental Testing for Electric and Electronic Products--Terms and Definitions (eqv IEC 60068-5-2: 1990)
GB/T 2423.1-2001 Environmental Testing for Electric and Electronic Products--Part 2: Test Methods--Tests A: Cold (idt IEC 60068-2-1: 1990)
GB/T 2423.2-2001 Environmental Testing for Electric and Electronic Products--Part 2: Test Methods--Tests B: Dry Heat (idt IEC 60068-2-2: 1974)
GB/T 2423.3-1993 Basic Environmental Testing Procedures for Electric and Electronic Products--Test Ca: Damp Heat, Steady State (eqv IEC 60068-2-3:1994)
GB/T 2423.4-1993 Basic Environmental Testing Procedures for Electric and Electronic Products--Test Db: Damp Heat, Cyclic (eqv IEC 60068-2-30: 1980)
GB/T 2423.5-1995 Environmental Testing for Electric and Electronic Products--Part 2: Test Methods--Test Ea and Guidance: Shock (idt IEC 60068-2-27: 1987)
GB/T 2423.10-1995 Environmental Testing for Electric and Electronic Products--Part 2: Test Methods--Test Fc and Guidance: Vibration (Sinusoidal) (idt IEC 60068-2-6: 1982)
GB/T 2423.19-1981 Electric and Electronic Products--Basic Environmental Test Regulations for Electricians--Test Kc: the Sulphur Dioxide Method at the Point of Contact and the Connecting Element
GB/T 17626.2-1998 Electromagnetic Compatibility--Testing and Measurement Techniques--Electrostatic Discharge Immunity Test (idt IEC 61000-4-2: 1995)
GB/T 17626.3-1998 Electromagnetic compatibility--Testing and Measurement Techniques--Radiated, Radio-frequency, Electromagnetic Field Immunity Test (idt IEC 61000-4-3: 1995)
GB/T 17626.4-1998 Electromagnetic Compatibility--Testing and Measurement Techniques--Electrical Fast Transient/burst Immunity Test (idt IEC 61000-4-4: 1995)
GB/T 17626.5-1999 Electromagnetic Compatibility--Testing and Measurement Techniques--Surge Immunity Test (idt IEC 61000-4-5: 1995)
GB/T 17626.6-1998 Electromagnetic Compatibility--Testing and Measurement Techniques--Immunity to Conducted Disturbances, Induced by Radio-frequency Fields (idt IEC 61000-4-6: 1996)
GB/T 17626.11-1999 Electromagnetic Compatibility--Testing and Measurement Techniques--Voltage Dips, Short Interruptions and Voltage Variations Immunity Tests (idt IEC 61000-4-11: 1994)
3. General Provisions
This Standard is formulated with a view to provide a unified test method that can reproduce the environment for fire electronic products.
Standards on fire electronic products shall be considered according to the environmental conditions that are likely to be encountered by the products and analyzed comprehensively from technology and economy prospects, and then, make specific provisions for the test method (condition) and severities adopted.
3.1 Test Category
The tests listed in this Standard are classified into two kinds:
I-type: running test
Such kind of tests are mainly judging whether the products meet the functional requirements under environmental test condition, which aims to inspect the capability of products under normal working in the operating ambient and verify the immunity from interference of the products under the operating ambient. In their testing process, all products are under normal monitoring state.
II-type: endurance test
This kind of tests are made to accelerate the impact of regular service environmental condition on the products, further to determine the products' performance, and assess the residual impact of the test environment on the products under off working state (non-instantaneous effect), which aims to verify the capability of products enduring the operating ambient for a long time.
3.2 Test Projects
Test projects specified in this Standard see Table 1: