This Standard specifies coding methods, structural types, technical requirements, measurement methods, inspection rules, markings and rustproof packaging of needle bearings (hereinafter referred to as bearings) for automobile manual transmission gear.
This Standard is applicable to the production, inspection and acceptance of bearings.
2 Normative References
The following documents contain provisions which, through reference in this text, constitute provisions of this Standard. For dated reference, subsequent amendments to (excluding the correction contents), or revisions of, any of these publications do not apply, however, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. For dated normative references, the latest edition of the document referred to applies.
GB/T 272-1993 Rolling Bearing-Identification Code
GB/T 307.1-2005 Rolling Bearings-Radial Bearings-Tolerances (ISO 492: 2002, MOD)
GB/T 307.2-2005 Rolling Bearings-Tolerances-Part 2: Measuring and Gauging Principles and Methods (ISO 1132-2: 2001, MOD)
GB/T 307.3-2005 Rolling Bearings-General Technical Regulations
GB/T 2828.1-2003 Sampling Procedures for Inspection by Attributea-Part 1: Sampling Schemes Indexed by Acceptance Quality Limit (AQL) for Lot-by-lot Inspection (ISO 2859-1: 1999, IDT)
GB/T 3077-1999 Alloy Structure Steels
GB/T 4199-2003 Rolling Bearings-Tolerances-Part 1: Terms and Definitions (ISO 1132-1: 2000, MOD)
GB/T 4604-2006 Rolling Bearings-Radial Internal Clearance (ISO 5753: 1991, MOD)
GB/T 4605-2003 Rolling Bearings-Thrust Needle Roller and Cage Assemblies, Thrust Washers
GB/T 6930-2002 Rolling Bearings-Vocabulary (ISO 5593: 1997, IDT)
GB/T 7811-2007 Rolling Bearings-Symbols for Quantities (ISO 15241: 2001, IDT)
GB/T 8597-2003 Rolling Bearings-Rust Proof Packaging
GB/T 13237-1991 Cold-Rolled Quality Carbon Structural Steel Shects and Strips
GB/T 18254-2002 High-Carbon Chromium Bearing Steel
GB/T 20056-2006 Rolling Bearings-Radial Needle Roller and Cage Assemblies-Dimensions and Tolerances (ISO 3030: 1996, MOD)
GB/T 24605-2009 Rolling Bearings-Marking for Products
GB/T 24607-2009 Rolling bearings-Test and Assessment for Life and Reliability
GB/T 25769-2010 Rolling Bearings-Measuring Methods for Radial Internal Clearance
JB/T 1255-2001 Specification for Heat-Treatment of Rolling Bearing Parts Made from High Carbon Chromium Steel
JB/T 2974-2004 Rolling Bearings-Identification Code-Supplemental Regulations
JB/T 6639-2004 Rolling Bearing Parts-Skeleton Acrylonitrile-buta-diene Copolymers Seal-Specifications
JB/T 6641-2007 Rolling Bearings-Residual Magnetism and Its Assessment Method
JB/T 7048-2002 Rolling Bearing Parts-Plastic Cage-Specifications
JB/T 7050-2005 Rolling Bearings-Assessment Methods for Cleanliness
JB/T 7051-2006 Rolling Bearing parts-Methods for the Measurement and Assessment of Surface Roughness
JB/T 7363-2002 Specifications for Carbonitriding Heat Treatment of Rolling Bearing Parts
JB/T 8878-2001 Rolling Bearings - Drawn up Needle Roller Bearings - Specifications
JB/T 8881-2001 Specifications for Carburizing Heat Treatment of Rolling Bearing Parts
JB/T 10336-2002 Rolling Bearings and Parts-Supplementary Specifications
JB/T 10337-2002 Rolling Bearing Parts-Pressing Cage-Specifications
YB/T 5058-2005 Cold-Rolled Spring and Tool Steel Strips
