1 Scope
This part of JB/T 5000 specifies technical requirements, testing method and drawing marking of steel welding parts.
This part is applicable to the steel welding parts welded by methods such as shielded metal arc welding, gas shielded welding and submerged-arc welding.
Where no special requirements are stated in the product drawing, technical document or technical specifications for procurement, all shall meet those specified in this part.
2 Normative References
The following normative documents contain provisions which, through reference in this Part of JB/T 5000, constitute provisions of this Part. For dated reference, subsequent amendments to (excluding correction to), or revisions of, any of these publications do not apply. However, the parties whose enter into agreement according to this Part are encouraged to research whether the latest editions of these references are applied or not. For undated references, the latest edition of the normative document is applicable to this standard.
GB/T 324 Welds-symbolic representation on drawings (GB/T324-1988,eqv ISO 2553:1989)
GB/T 985 Basic Forms and Sizes of Weld Grooves for Gas Welding, Manual Arc Welding and Gas-shielded Arc Welding
GB/T 986 Basic Forms and Sizes of Submerged Arc Weld Grooves
GB/T 2649 Methods of sampling for mechanical properties tests of welded joint
GB/T 2650 Impact Test Methods on Welded Joints
GBTF 2651 Tensile test method on welded joints
GB/T 2652 Tensile Test Methods on Weld and Deposited Metal
GB/T 2653 Methods of Bend and Compression Tests for Welded Joint
GB/T 2654 Methods of Hardness Tests for Welded Joint and Surfacing Metal
GB/T 3323 Radiographic Examination of Fusion Welded Joints in Metallic Materials (GB/T 3323-2005, EN 135:1997, MOD)
GB/T 11345 Method for Manual Ultrasonic Testing and Classification of Testing Results for Ferritic Steel Welds
JB/T 3223 Quality management requirements of welding material
JB/T 4735 Steel Welded Atmospheric Pressure Vessels
JB/T 5000.2 Heavy Mechanical General Techniques and Standards - Part 2: Oxygen cutting workpiece
JB/T 5000.11 Heavy Mechanical General Techniques and Standards - Part 11: Attached piping
JB/T 5000.12 Heavy Mechanical General Techniques and Standards - Part 12: Paint
JB/T 5926 Vibrating stress relief effect-evaluation methods
JB/T 6046 Post-weld heat treatment methods for welded members of carbon steel and low alloy steel
JB/T 6061 Non-destructive testing-Magnetic Particle testing of Welds
JB/T 7949 Weld outer dimensions for steel construction
3 General Requirements
3.1 The manufacturing of welding (weldment) shall meet the requirements of design drawing, process document and this Part.
3.2 The steel type, specification and dimension of the materials (steel plate, section steel and steel pipe etc.) used to manufacture welding shall meet the requirements of design drawing, and material substitution shall be transacted with substitution sheet in accordance with relevant provisions.
3.3 The materials, welding materials (welding rod, welding wire, welding flux, shielding gas etc.) used to manufacture welding entering factory, they may enter the storehouse after being accepted by the quality control division according to the "material pre-working acceptance regulations" of the factory based on the certificate of compliance provided by the supplier, as well as corresponding national (professional) standard and ordering requirements.
We use strictly necessary cookies to make our site work. We would also like to set optional analytics cookies
to help us improve it, and targeting cookies. We won't set optional cookies unless you enable them.
For more detailed information about the cookies we use, see our
Cookies Notice.
By clicking "Accept all cookies", you agree to the storing of cookies on your device for the purposes set out
in our Cookies Notice. Click "Reject non-essential" to refuse optional cookies.
Strictly necessary cookies are always active and cannot be disabled.
Cookie Consent Manager
Your Privacy
Websites may store or retrieve information on your browser, mostly in the form of cookies.
This information might be about you, your preferences, or your device and is mostly used to make
the site work as you expect it to. The information does not usually directly identify you, but it
can give you a more personalized web experience. Because we respect your right to privacy, you can
choose not to allow some types of cookies. Click on the different category headings to find out more
and change our default settings. However, blocking some types of cookies may impact your experience
of the site and the services we are able to offer.
These cookies are required for the operation of our website and use of its features, and therefore
cannot be switched off in our systems. They are usually only set in response to actions made by you
which amount to a request for services, such as setting your privacy preferences, logging in, or
filling in forms.
Functional Cookies
These cookies are optional and are used to remember the choices you have made.
These cookies are optional and are used to collect information on how visitors use our website.
Targeting Cookies
These cookies may be set to deliver advertising that is more relevant to you and your interests,
or to measure advertising effectiveness. California residents may opt out of the sale or sharing
of personal information via Do Not Sell/Share.
If this site does not currently run advertising pixels, enabling this category has no effect until such tools are added.