1 Scope
This part of JB/T 5000 specifies the technical requirements, test methods, acceptance regulations, sign and certification of non ferrous casting.
This part is applicable to the copper alloy, aluminum alloy, and zinc alloy castings produced by the sand mold, metal mold and centrifugal casting methods.
2 Normative References
The provisions in following documents, through reference in this Part of JB/T 5000, constitute the articles of this Part. For dated reference, subsequent amendments to (excluding corrigenda), or revisions of, any of these publications do not apply. However, all parties coming to an agreement according to this standard are encouraged to study whether the latest edition of these documents is applicable. For undated references, the latest edition of the normative document is applicable to this part.
GB/T 228 "Metallic Materials-Tensile Testing at Ambient Temperature" (GB/T 228-2002, eqv ISO 6892: 1998)
GB/T231.1 Metallic materials - Brinell hardness test - Part 1: Test method GB/T 231.1-2002, eqv ISO 6506-1:1999(E)
GB/T 1173 Casting aluminum alloys (GB/T 1173-1995, neq. ASTM B26:1992)
GB/T 1175 "Casting Zinc Alloys"
GB/T 1176 "Specification for cast copper alloys" (GB/T 1176-1987, neq ISO 1338: 1977)
GB/T 6060.1 Roughness comparison specimens--Cast surfaces (GB/T 6060.1-1997, eqv ISO 2632-3:1979)
GB/T 6414 Castings--System of dimensional tolerances and machining allowances (GB/T 6414-1999, eqv ISO 8062:1994)
JB/T 5000.13 Heavy Mechanical General Techniques and Standards-Part 13: Packing
3 Technical Requirements
3.1 Chemical Composition and Mechanical Property
3.1.1 Chemical composition and mechanical property of aluminum alloy casting shall meet the requirements of GB/T 1173.
3.1.2 Chemical composition and mechanical property of zinc alloy casting shall meet the requirements of GB/T 1175.
3.1.3 Chemical composition and mechanical property of copper alloy casting shall meet the requirements of GB/T 1173.
3.1.3.1 For the copper alloy castings that bear heavy load and are used for key positions, such as worm gear, wheel rim, and screw box and those whose maximum size is more than 500mm, mechanical property shall be used as the key acceptance basis. Little deviation is permitted in the chemical composition and its value shall be 10% of upper and lower limits of percentage composition for each main component.
3.1.3.2 For various bushings, bearing bush as well as sliding plate type copper alloy casting that bear light loads, are used for general positions and the maximum size is not greater than 500mm, chemical composition or mechanical property both can be taken as the acceptance basis; if either of them is qualified, it can be considered as qualification; the other one is only used for reference but it must have data.
3.2 Dimensional Tolerance and Configuration of Tolerance Zone
3.2.1 Dimensional tolerance shall meet the requirements of GB/T 6414; common class code and tolerance see Table 1. The same casting shall select the same tolerance class and tolerance class shall be selected according to basic size of rough casting.
3.2.2 Dimensional tolerance zone for Castings shall be distributed symmetrically in relation To basic size of rough casting, namely half of tolerance shall be located above the basic size and other half shall be below the basic size (see Figure 1). If there is special requirement, tolerance zone also can be distributed asymmetrically but must be noted in drawing or specified in technological document.
We use strictly necessary cookies to make our site work. We would also like to set optional analytics cookies
to help us improve it, and targeting cookies. We won't set optional cookies unless you enable them.
For more detailed information about the cookies we use, see our
Cookies Notice.
By clicking "Accept all cookies", you agree to the storing of cookies on your device for the purposes set out
in our Cookies Notice. Click "Reject non-essential" to refuse optional cookies.
Strictly necessary cookies are always active and cannot be disabled.
Cookie Consent Manager
Your Privacy
Websites may store or retrieve information on your browser, mostly in the form of cookies.
This information might be about you, your preferences, or your device and is mostly used to make
the site work as you expect it to. The information does not usually directly identify you, but it
can give you a more personalized web experience. Because we respect your right to privacy, you can
choose not to allow some types of cookies. Click on the different category headings to find out more
and change our default settings. However, blocking some types of cookies may impact your experience
of the site and the services we are able to offer.
These cookies are required for the operation of our website and use of its features, and therefore
cannot be switched off in our systems. They are usually only set in response to actions made by you
which amount to a request for services, such as setting your privacy preferences, logging in, or
filling in forms.
Functional Cookies
These cookies are optional and are used to remember the choices you have made.
These cookies are optional and are used to collect information on how visitors use our website.
Targeting Cookies
These cookies may be set to deliver advertising that is more relevant to you and your interests,
or to measure advertising effectiveness. California residents may opt out of the sale or sharing
of personal information via Do Not Sell/Share.
If this site does not currently run advertising pixels, enabling this category has no effect until such tools are added.